CCIE labbing with Asasel’s IOU 4.3

Cisco has requested that I delete this blog post.

They have been nice so far…. so this post in going, going… gone! 

Juniper Brocade Force10

Tagged with: , , , ,
Posted in CCIE studies
17 comments on “CCIE labbing with Asasel’s IOU 4.3
  1. Amemon says:

    I used it once and second time when I connect to this IOU – I dont get to see the ip address. How to fix that ?
    I am able to see the ip address on the command prompt but how to see/set the ip address in the IOU ?

    • Brent says:

      This runs on Busybox, I believe. You should be able to use ifconfig. Or you should be able to IP in your VM config. I use VirtualBox and can change the interface config in the network settings. HTH

  2. YOU ARE A FOOL says:

    YOU ARE A FOOL… WHY POST SOMETHING THAT WE CAN’T GET ARE YOU TRYING TO OPPRESS???

  3. cisco_kid says:

    Great videos. Can you tell me the VMware setting for version 4.3 as it seems to be different from flyxj. I have no problem running 4.3 on VMware just don’t know what the IP’s are and I can’t telnet into the POD’s.

    Thanks in advance

  4. paresh says:

    sir,
    very nice post and very useful for me to setup iou thk very much.

  5. Ronaldo says:

    Wowwww… “AND DO NOT ASK ME WHERE TO FIND IT” why you talk this? share this information, send the information, share IOU file, or file is not “pirate” for sale? the sales are legal? so not pirating more, not sale, sharing with the community.

    Tks.

    • Brent says:

      People need to do a little work on their own here. If you can’t find Asasel’s version, or feel compelled to go the licensed route then you should ask your Cisco SE to work out a license for you. No harm in asking, especially if you indicate that it will help your organization make purchasing decisions in the future.

  6. Rizwan says:

    the ip address issue is mainly corrected from Virtual network Editor under edit in VMware. Make sure you have set NAT and the check box (connect a virtual host adapter, use local DHCP service) is marked. Now check again in the menu IP address will be shown against port.

  7. Rizwan says:

    and plus don’t be rude guys..IOU is not an official release and Cisco can ban your ass off if they find out that you are spreading it illegally as FLYXJ is already banned for life so chill out and give the lad a break!!

  8. Ronaldo says:

    Not everyone has this break, it has marked his examination, it is obvious that you can not spread, 4shared and put in a post, but can at least e-mail, because someone got the shared file, then do the same, I referred to the way they expressed it, still I think it just …

  9. zayalaksme says:

    - thanks for tell about IOU
    – i have some doubts when labbing on iou
    – can anybody plz suggests where I can share these doubts while labbing on IOU
    – plz suggest me some good forums

  10. zo3fol says:

    how can I load INE volumes II & III & IV ? I only have the option to load Volume 1, however the topology/initial configuration files are different, unless I have missed something.

  11. ar3k says:

    Hi,

    can somebody help me with the IOU ? When I load the basic IP config from INE submenu ang this error msg from the switch:

    Rack1SW2#
    *Mar 19 12:52:34.775: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse from (tftp://255.255.255.255/rack1sw2-confg) failed
    Rack1SW2#
    %Error opening tftp://255.255.255.255/rack1sw2.cfg (Timed out)
    *Mar 19 12:53:12.795: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse from (tftp://255.255.255.255/rack1sw2.cfg) failed
    Rack1SW2#

    any ideas how to solve it ??

    cheers

  12. Mohammed says:

    you can resolved by configuring in all devices

    no service config

    after issue above command you need to save copy run start.

    after that just reload command to all this device my issue command, not vm.

    Note: dont restart VM.

    once you done just take snapshot in VM then you will be there where you are.

    enjoy.. :)

  13. prakin says:

    Hi guys,

    I have problem on loading INE submenu, once routers and switches are loaded and i checked the status of the pod, its says IOU is not running error, any ideas how to solve this??? please help

Leave a Reply

Your email address will not be published. Required fields are marked *

*

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>